IPAC2018 - List of Authors (Keane, R.T.)

Paper	Title	Page
TUZGBD3	Beam Diagnostics for the APS MBA Upgrade	1204
	N. Sereno, N.D. Arnold, R.W. Blake, A.R. Brill, H. Bui, J. Carwardine, G. Decker, L. Emery, T. Fors, P.S. Kallakuri, R.T. Keane, R.M. Lill, D.R. Paskvan, A.F. Pietryla, H. Shang, X. Sun, S. Veseli, J. Wang, S. Xu, B.X. Yang ANL, Argonne, Illinois, USA
	The Advanced Photon Source (APS) is currently in the preliminary design phase for a multi-bend acromat (MBA) lattice upgrade. Beam stability is critical where the requirements are driven from the beam size which is expected to approach 4 microns vertically at the insertion device (ID) source points. AC rms beam stability requirements are defined as 10 % the minimum source size at the ID in the band 0.01-1000 Hz. The vertical plane stability goal is the most ambitious requiring a stability of 400 nm at the ID source point. In addition, long term drift defined as motion over a seven day timescale can be no more than 1 micron. In order to achieve these demanding beam stability requirements, a suite of beam diagnostics will be required including rf BPMs, X-ray BPMs, a mechanical motion measurement system, beam size monitors and a real time orbit feedback system. In addition, a tune measurement system, transverse multi-bunch feedback system and current monitors are planned for the upgrade. We report on the beam diagnostics design and APS storage ring R&D results used to inform the design.
	Slides TUZGBD3 [16.748 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-TUZGBD3
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEPAF005	A Fast Beam Interlock System for the Advanced Photon Source Particle Accumulator Ring	1815
	J.C. Dooling, M. Borland, K.C. Harkay, R.T. Keane, B.J. Micklich, C. Yao ANL, Argonne, Illinois, USA
	Funding: Work supported by the U.S. Department of Energy, Office of Science, Of- fice of Basic Energy Sciences, under Contract No. DE-AC02-06CH11357. A fast beam interlock system for the Advanced Photon Source (APS) Particle Accumulator Ring (PAR) based on the detection of Cerenkov light is proposed for high-charge operations associated with the APS Upgrade (APS-U). Light is generated from lost electrons passing through high-purity, fused-silica fiber optic cable. The cable acts as both radiator and light pipe to a Pb-shielded photomultiplier tube. Results from a prototype installation along the PAR south wall have shown excellent sensitivity, linearity, and reproducibility after 10,000 hours of operation to date with little change in the optical transmission of the fiber. High sensitivity allows more accurate measurement of low-level loss than possible with current monitors. The radiator and detector provide a much faster response than the installed gamma or neutron detectors. A faster, more accurate response to electron loss will be important as we run with higher charge and consider operating at increased energy for APS-U. Initial calibration measurements of the prototype system with radiation monitors for various loss scenarios are discussed. Comparison of the scenarios with simulations are presented.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-WEPAF005
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEPMF008	Preliminary Designs and Test Results of Bipolar Power Supplies for APS Upgrade Storage Ring	2381
	J. Wang, I.A. Abid, R.T. Keane, G.S. Sprau ANL, Argonne, Illinois, USA
	Funding: Work supported by the U.S. Department of Energy, Office of Science, Office of Basic Energy Sciences, under Contract No. DE-AC02-06CH11357. The upgrade (APS-U) of the APS storage ring requires more than 1200 bipolar power supplies. Based on the performance requirement, the power supplies can be divided into two categories: fast bipolar power supplies for fast correctors and slow bipolar power supplies for trim coils and slow correctors. The common requirement of the power supplies is a bipolar output current up to ±15 A. The main difference is that the fast corrector power supplies require a small-signal bandwidth of 10 kHz. A prototype DC/DC power converter utilizing a MOSFET H-bridge circuit with a 500 kHz PWM was successfully developed through the R&D program, achieving the required bandwidth with less than 3-dB attenuation for a signal 0.5% of ±15 A. After the successful R&D program, the preliminary designs were performed to further improve the performance and to finalize the schematics, the PCB layouts, and the power supply constructions. The two types of the power supplies share the majority of the designs and features, with minor differences for the different bandwidth requirement. This paper presents the preliminary design, the key power supply functions and features, and the test results.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-WEPMF008
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

Paper

Title

Page

Beam Diagnostics for the APS MBA Upgrade

1204

N. Sereno, N.D. Arnold, R.W. Blake, A.R. Brill, H. Bui, J. Carwardine, G. Decker, L. Emery, T. Fors, P.S. Kallakuri, R.T. Keane, R.M. Lill, D.R. Paskvan, A.F. Pietryla, H. Shang, X. Sun, S. Veseli, J. Wang, S. Xu, B.X. Yang
ANL, Argonne, Illinois, USA

The Advanced Photon Source (APS) is currently in the preliminary design phase for a multi-bend acromat (MBA) lattice upgrade. Beam stability is critical where the requirements are driven from the beam size which is expected to approach 4 microns vertically at the insertion device (ID) source points. AC rms beam stability requirements are defined as 10 % the minimum source size at the ID in the band 0.01-1000 Hz. The vertical plane stability goal is the most ambitious requiring a stability of 400 nm at the ID source point. In addition, long term drift defined as motion over a seven day timescale can be no more than 1 micron. In order to achieve these demanding beam stability requirements, a suite of beam diagnostics will be required including rf BPMs, X-ray BPMs, a mechanical motion measurement system, beam size monitors and a real time orbit feedback system. In addition, a tune measurement system, transverse multi-bunch feedback system and current monitors are planned for the upgrade. We report on the beam diagnostics design and APS storage ring R&D results used to inform the design.

Slides TUZGBD3 [16.748 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-TUZGBD3

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEPAF005

A Fast Beam Interlock System for the Advanced Photon Source Particle Accumulator Ring

1815

J.C. Dooling, M. Borland, K.C. Harkay, R.T. Keane, B.J. Micklich, C. Yao
ANL, Argonne, Illinois, USA

Funding: Work supported by the U.S. Department of Energy, Office of Science, Of- fice of Basic Energy Sciences, under Contract No. DE-AC02-06CH11357.
A fast beam interlock system for the Advanced Photon Source (APS) Particle Accumulator Ring (PAR) based on the detection of Cerenkov light is proposed for high-charge operations associated with the APS Upgrade (APS-U). Light is generated from lost electrons passing through high-purity, fused-silica fiber optic cable. The cable acts as both radiator and light pipe to a Pb-shielded photomultiplier tube. Results from a prototype installation along the PAR south wall have shown excellent sensitivity, linearity, and reproducibility after 10,000 hours of operation to date with little change in the optical transmission of the fiber. High sensitivity allows more accurate measurement of low-level loss than possible with current monitors. The radiator and detector provide a much faster response than the installed gamma or neutron detectors. A faster, more accurate response to electron loss will be important as we run with higher charge and consider operating at increased energy for APS-U. Initial calibration measurements of the prototype system with radiation monitors for various loss scenarios are discussed. Comparison of the scenarios with simulations are presented.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-WEPAF005

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEPMF008

Preliminary Designs and Test Results of Bipolar Power Supplies for APS Upgrade Storage Ring

2381

J. Wang, I.A. Abid, R.T. Keane, G.S. Sprau
ANL, Argonne, Illinois, USA

Funding: Work supported by the U.S. Department of Energy, Office of Science, Office of Basic Energy Sciences, under Contract No. DE-AC02-06CH11357.
The upgrade (APS-U) of the APS storage ring requires more than 1200 bipolar power supplies. Based on the performance requirement, the power supplies can be divided into two categories: fast bipolar power supplies for fast correctors and slow bipolar power supplies for trim coils and slow correctors. The common requirement of the power supplies is a bipolar output current up to ±15 A. The main difference is that the fast corrector power supplies require a small-signal bandwidth of 10 kHz. A prototype DC/DC power converter utilizing a MOSFET H-bridge circuit with a 500 kHz PWM was successfully developed through the R&D program, achieving the required bandwidth with less than 3-dB attenuation for a signal 0.5% of ±15 A. After the successful R&D program, the preliminary designs were performed to further improve the performance and to finalize the schematics, the PCB layouts, and the power supply constructions. The two types of the power supplies share the majority of the designs and features, with minor differences for the different bandwidth requirement. This paper presents the preliminary design, the key power supply functions and features, and the test results.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-WEPMF008

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)