IPAC2018 - List of Authors (Hsiung, G.-Y.)

Paper	Title	Page
THPAL057	Development of the Aluminum Beam Duct for the Ultra-Low Emittance Light Source	3775
	G.-Y. Hsiung, J.-R. Chen, C.M. Cheng, S-N. Hsu, H.P. Hsueh, Y.C. Yang NSRRC, Hsinchu, Taiwan J.-R. Chen National Tsing Hua University, Hsinchu, Taiwan
	The future light source with ultra-low emittance, typically < 500 pm rad, requests the beam duct with inner aperture < 20 mm for the electron storage ring. Besides, the cross section of the beam duct must be kept smooth for lowering the impedance. The aluminum extruded beam duct of 10 mm inside and 1 ~ 2 m in length was developed for this purpose. The beam duct was machined in ethanol to obtain a clean surface for a lower thermal outgassing rate. To mitigate the impedance of the flange connection, a special designed diamond-edge gasket and the aluminum flange without knife edge were developed. The inner diameters of both flange and gasket, 10 mm, are the same as that of beam duct. The sealing of the gasket has been proved leak-tight. The ultimate pressure and the thermal outgassing rate of the beam duct has achieved < 2.0·10^-10 Torr and < 1.4·10^-13 Torr l/(s cm²), respectively after baking. Those results fulfill both the ultrahigh vacuum and lowest impedance are applicable for the next generation ultra-low emittance light source.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-THPAL057
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THPAL058	Effect of Ozonated Water Cleaning on Photon Stimulated Desorption in a Stainless Steel Chamber	3778
	C.M. Cheng, C.K. Chan, C.-C. Chang, Y.T. Cheng, J. -Y. Chuang, G.-Y. Hsiung, L.H. Wu, Y.C. Yang NSRRC, Hsinchu, Taiwan
	Aluminium vacuum chambers cleaned with ozonated water show a reduction of residual carbon and lower surface outgassing rate after baking. We would like to investigate if stainless steel chambers show similar ef-fects. A stainless steel test chamber was cleaned by stand-ard chemical cleaning only and then compared with an-other one after immersion in 30ppm ozonated water for thirty minutes. Both samples were baked, then photon exposed and the photon desorption yields were deter-mined by vacuum gauges and residual gas analysers at the TLS 19B beamline. The test results on photon stimulated desorption yields and partial pressure variations with and without ozonated water cleaning of the stainless steel tubes will be discussed in some detail.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-THPAL058
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

Paper

Title

Page

Development of the Aluminum Beam Duct for the Ultra-Low Emittance Light Source

3775

G.-Y. Hsiung, J.-R. Chen, C.M. Cheng, S-N. Hsu, H.P. Hsueh, Y.C. Yang
NSRRC, Hsinchu, Taiwan
J.-R. Chen
National Tsing Hua University, Hsinchu, Taiwan

The future light source with ultra-low emittance, typically < 500 pm rad, requests the beam duct with inner aperture < 20 mm for the electron storage ring. Besides, the cross section of the beam duct must be kept smooth for lowering the impedance. The aluminum extruded beam duct of 10 mm inside and 1 ~ 2 m in length was developed for this purpose. The beam duct was machined in ethanol to obtain a clean surface for a lower thermal outgassing rate. To mitigate the impedance of the flange connection, a special designed diamond-edge gasket and the aluminum flange without knife edge were developed. The inner diameters of both flange and gasket, 10 mm, are the same as that of beam duct. The sealing of the gasket has been proved leak-tight. The ultimate pressure and the thermal outgassing rate of the beam duct has achieved < 2.0·10^-10 Torr and < 1.4·10^-13 Torr l/(s cm²), respectively after baking. Those results fulfill both the ultrahigh vacuum and lowest impedance are applicable for the next generation ultra-low emittance light source.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-THPAL057

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THPAL058

Effect of Ozonated Water Cleaning on Photon Stimulated Desorption in a Stainless Steel Chamber

3778

C.M. Cheng, C.K. Chan, C.-C. Chang, Y.T. Cheng, J. -Y. Chuang, G.-Y. Hsiung, L.H. Wu, Y.C. Yang
NSRRC, Hsinchu, Taiwan

Aluminium vacuum chambers cleaned with ozonated water show a reduction of residual carbon and lower surface outgassing rate after baking. We would like to investigate if stainless steel chambers show similar ef-fects. A stainless steel test chamber was cleaned by stand-ard chemical cleaning only and then compared with an-other one after immersion in 30ppm ozonated water for thirty minutes. Both samples were baked, then photon exposed and the photon desorption yields were deter-mined by vacuum gauges and residual gas analysers at the TLS 19B beamline. The test results on photon stimulated desorption yields and partial pressure variations with and without ozonated water cleaning of the stainless steel tubes will be discussed in some detail.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-THPAL058

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)