IPAC2018 - List of Authors (Chmielinska, A.)

Paper	Title	Page
WEPMF089	Measurements of Electromagnetic Properties of Ferrites as a Function of Frequency and Temperature	2592
	A. Chmielinska, M.J. Barnes, F. Caspers, B.K. Popovic, C. Vollinger CERN, Geneva, Switzerland
	Fast kicker magnets are used to inject beam into and extract beam out of the CERN accelerator rings. These kickers are often ferrite loaded transmission line type magnets with a rectangular shaped aperture through which the beam passes. The interaction of the beam with the resistive part of the longitudinal beam coupling impedance leads to power dissipation and heating of different elements in the accelerator ring. In particular, power deposition in the kicker magnets can be a limitation: if the temperature of the ferrite yoke exceeds the Curie temperature, the beam will not be properly deflected. In addition, the imaginary portion of the beam coupling impedance contributes to beam instabilities. A good knowledge of electromagnetic properties of materials up to GHz frequency range is essential for a correct impedance evaluation. This paper presents the results of transmission line measurements of complex initial permeability and permittivity for different ferrite types. We present an approach for deriving electromagnetic properties as a function of both frequency and temperature; this information is required for simulating ferrite behaviour under realistic operating conditions.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-WEPMF089
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEPMK003	An Upgraded LHC Injection Kicker Magnet	2632
	M.J. Barnes, C. Bracco, G. Bregliozzi, A. Chmielinska, L. Ducimetière, B. Goddard, T. Kramer, H. Neupert, L. Vega Cid, V. Vlachodimitropoulos, W.J.M. Weterings, C. Yin Vallgren CERN, Geneva, Switzerland A. Chmielinska EPFL, Lausanne, Switzerland
	Funding: Work supported by the HL-LHC project. An upgrade of the LHC injection kickers is necessary for HL-LHC to avoid excessive beam induced heating of these magnets: the intensity of the HL-LHC beam will be twice that of LHC. In addition, in the event that it is necessary to exchange an injection kicker magnet, the newly installed kicker magnet would limit HL-LHC operation for a few hundred hours due to dynamic vacuum activity. Extensive studies have been carried out to identify practical solutions to these problems: these include redistributing a significant portion of the beam induced power deposition to ferrite parts of the kicker magnet which are not at pulsed high voltage and water cooling of these parts. Furthermore a surface coating, to mitigate dynamic vacuum activity, has been selected. The results of these studies, except for water cooling, have been implemented on an upgraded LHC injection kicker magnet: this magnet was installed in the LHC during the 2017-18 Year End Technical Stop. This paper presents the upgrades, including some test and measurement results.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-WEPMK003
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEPMK005	Preliminary Results from Validation Measurements of the Longitudinal Power Deposition Model for the LHC Injection Kicker Magnet	2636
	V. Vlachodimitropoulos, M.J. Barnes, A. Chmielinska CERN, Geneva, Switzerland A. Chmielinska EPFL, Lausanne, Switzerland
	During Run 1 of the LHC, one of the injection kicker magnets (MKIs) exhibited an excessively high ferrite temperature, caused by coupling of the high intensity beam to the real impedance of the magnet. Beam-screen upgrades, implemented during Long Shutdown 1 (LS1), have been very effective in reducing beam coupling impedance and since then the MKIs have not limited LHC's availability. However, temperature measurements during operation have shown that one end of the MKI's ferrite yoke is consistently hotter than the other. Detailed simulation models and data post-processing algorithms have been developed to understand and mitigate the observed behaviour. In the present paper, the model used to obtain the power loss distribution along the magnet is presented. The model is subsequently applied to two MKI design configurations under study: (i) the one currently in operation and (ii) an upgraded magnet that was installed in the LHC tunnel during the Year End Technical Stop (YETS) 2017/18. In order to validate the expected behaviour a novel measurement technique was developed, applied in both configurations and compared to predictions. The results obtained are reported and conclusions regarding the effectiveness of the design are drawn.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-WEPMK005
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

Paper

Title

Page

Measurements of Electromagnetic Properties of Ferrites as a Function of Frequency and Temperature

2592

A. Chmielinska, M.J. Barnes, F. Caspers, B.K. Popovic, C. Vollinger
CERN, Geneva, Switzerland

Fast kicker magnets are used to inject beam into and extract beam out of the CERN accelerator rings. These kickers are often ferrite loaded transmission line type magnets with a rectangular shaped aperture through which the beam passes. The interaction of the beam with the resistive part of the longitudinal beam coupling impedance leads to power dissipation and heating of different elements in the accelerator ring. In particular, power deposition in the kicker magnets can be a limitation: if the temperature of the ferrite yoke exceeds the Curie temperature, the beam will not be properly deflected. In addition, the imaginary portion of the beam coupling impedance contributes to beam instabilities. A good knowledge of electromagnetic properties of materials up to GHz frequency range is essential for a correct impedance evaluation. This paper presents the results of transmission line measurements of complex initial permeability and permittivity for different ferrite types. We present an approach for deriving electromagnetic properties as a function of both frequency and temperature; this information is required for simulating ferrite behaviour under realistic operating conditions.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-WEPMF089

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEPMK003

An Upgraded LHC Injection Kicker Magnet

2632

M.J. Barnes, C. Bracco, G. Bregliozzi, A. Chmielinska, L. Ducimetière, B. Goddard, T. Kramer, H. Neupert, L. Vega Cid, V. Vlachodimitropoulos, W.J.M. Weterings, C. Yin Vallgren
CERN, Geneva, Switzerland
A. Chmielinska
EPFL, Lausanne, Switzerland

Funding: Work supported by the HL-LHC project.
An upgrade of the LHC injection kickers is necessary for HL-LHC to avoid excessive beam induced heating of these magnets: the intensity of the HL-LHC beam will be twice that of LHC. In addition, in the event that it is necessary to exchange an injection kicker magnet, the newly installed kicker magnet would limit HL-LHC operation for a few hundred hours due to dynamic vacuum activity. Extensive studies have been carried out to identify practical solutions to these problems: these include redistributing a significant portion of the beam induced power deposition to ferrite parts of the kicker magnet which are not at pulsed high voltage and water cooling of these parts. Furthermore a surface coating, to mitigate dynamic vacuum activity, has been selected. The results of these studies, except for water cooling, have been implemented on an upgraded LHC injection kicker magnet: this magnet was installed in the LHC during the 2017-18 Year End Technical Stop. This paper presents the upgrades, including some test and measurement results.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-WEPMK003

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEPMK005

Preliminary Results from Validation Measurements of the Longitudinal Power Deposition Model for the LHC Injection Kicker Magnet

2636

V. Vlachodimitropoulos, M.J. Barnes, A. Chmielinska
CERN, Geneva, Switzerland
A. Chmielinska
EPFL, Lausanne, Switzerland

During Run 1 of the LHC, one of the injection kicker magnets (MKIs) exhibited an excessively high ferrite temperature, caused by coupling of the high intensity beam to the real impedance of the magnet. Beam-screen upgrades, implemented during Long Shutdown 1 (LS1), have been very effective in reducing beam coupling impedance and since then the MKIs have not limited LHC's availability. However, temperature measurements during operation have shown that one end of the MKI's ferrite yoke is consistently hotter than the other. Detailed simulation models and data post-processing algorithms have been developed to understand and mitigate the observed behaviour. In the present paper, the model used to obtain the power loss distribution along the magnet is presented. The model is subsequently applied to two MKI design configurations under study: (i) the one currently in operation and (ii) an upgraded magnet that was installed in the LHC tunnel during the Year End Technical Stop (YETS) 2017/18. In order to validate the expected behaviour a novel measurement technique was developed, applied in both configurations and compared to predictions. The results obtained are reported and conclusions regarding the effectiveness of the design are drawn.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-WEPMK005

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)