IPAC2018 - List of Authors (Bambade, P.)

Paper	Title	Page
TUZGBD5	Performance of Nanometre-Level Resolution Cavity Beam Position Monitors at ATF2	1212
	T. Bromwich, D.R. Bett, N. Blaskovic Kraljevic, R.M. Bodenstein, P. Burrows, G.B. Christian, C. Perry, R.L. Ramjiawan JAI, Oxford, United Kingdom S. Araki, A. Aryshev, T. Tauchi, N. Terunuma KEK, Ibaraki, Japan P. Bambade, S. Wallon LAL, Orsay, France S.W. Jang Korea University Sejong Campus, Sejong, Republic of Korea
	A system of three low-Q cavity beam position monitors (BPMs), installed in the interaction point (IP) region of the Accelerator Test Facility (ATF2) at KEK, has been designed and optimised for nanometre-level beam position resolution. The BPMs are used to provide an input to a low-latency, intra-train beam position feedback system deployed in single-pass, multi-bunch mode with the aim of demonstrating intra-train beam stabilisation on electron bunches of charge ~1 nC separated in time by 280 ns. In 2016 the BPM resolution was demonstrated to be below 50 nm using the raw measured vertical positions at the three BPMs. New results will be presented utilising integrated sampling of the raw waveforms, improved BPM alignment and modified cavities to demonstrate a vertical position resolution on the order of 20 nm.
	Slides TUZGBD5 [8.557 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-TUZGBD5
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEPAL037	Simulation Study on Luminosity Feedback for Horizontal Beam Stabilization at Superkekb	2250
	C.G. Pang, P. Bambade LAL, Orsay, France Y. Funakoshi, S. Uehara KEK, Ibaraki, Japan
	The SuperKEKB e⁺ e^- collider uses highly focused ultra-low emittance bunches colliding every 4 ns to reach a very high luminosity of 8× 10³⁵ cm^-2s^-1. It is quite essential to have an orbit feedback system at the Interaction Point (IP) to maintain the optimum overlap between the colliding beams in the presence of ground motion disturbances. For the horizontal motion, a luminosity monitoring system, based on measuring the rate of the Bhabha process at vanishing scattering angle, is developed as input signal to the feedback system. The relative precision needed for this monitor is studied in detail, for the different successive stages of luminosity operation, based on a full simulation of this system, including the detector, DAQ, lock-in amplifier, and feedback control.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-WEPAL037
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEPAL038	First Tests of Superkekb Fast Luminosity Monitors During 2018 Phase-2 Commissioning	2254
	C.G. Pang, P. Bambade, S. Di Carlo, D. Jehanno, V. Kubytskyi, Y. Peinaud, C. Rimbault LAL, Orsay, France Y. Funakoshi, S. Uehara KEK, Ibaraki, Japan
	The SuperKEKB e⁺e^- collider aims to reach a very high luminosity of 8× 10³⁵ cm^-2s^-1, by using highly focused ultra-low emittance bunches colliding every 4 ns, it is essential to have an orbit feedback system at the Interaction Point (IP) to maintain the optimum overlap between two colliding beams. Luminosity monitoring systems including LumiBelle2 and ZDLM as input to dithering feedback system used to stabilize the horizontal orbit at the IP were developed and will be described, including the detectors, mechanical set-up, DAQ. Preliminary measurements and analysis of background and first stage luminosity monitoring data collected will be reported and compared with simulation.
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-WEPAL038
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THYGBE4	Early Phase 2 Results of LumiBelle2 for the SuperKEKB Electron Ring	2934
	S. Di Carlo, P. Bambade, D. Jehanno, V. Kubytskyi, C.G. Pang, Y. Peinaud, C. Rimbault LAL, Orsay, France
	We report on the early SuperKEKB Phase 2 operations of the fast luminosity monitor (LumiBelle2 project). Fast luminosity monitoring is required by the dithering feedback system, which is used to stabilize the beam in the presence of horizontal vibrations. In this report, we focus on the operations related to the electron side of LumiBelle2. Diamond sensors are located 30 meters downstream of the IP, just above, beside, and below the electron beam pipe. During early Phase 2, the sensors are used to measure the background, arising from beam-gas scattering. We present the hardware design, the detection algorithm, and the analysis of the background measurements taken up-to-date. The results are then compared with a detailed simulation of the background, in order to well understand the physical processes involved. The simulation is performed using SAD for generation and tracking purposes, while Geant4 is used to calculate the energy deposition in the diamond sensors.
	Slides THYGBE4 [3.091 MB]
DOI •	reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-THYGBE4
Export •	reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

Paper

Title

Page

Performance of Nanometre-Level Resolution Cavity Beam Position Monitors at ATF2

1212

T. Bromwich, D.R. Bett, N. Blaskovic Kraljevic, R.M. Bodenstein, P. Burrows, G.B. Christian, C. Perry, R.L. Ramjiawan
JAI, Oxford, United Kingdom
S. Araki, A. Aryshev, T. Tauchi, N. Terunuma
KEK, Ibaraki, Japan
P. Bambade, S. Wallon
LAL, Orsay, France
S.W. Jang
Korea University Sejong Campus, Sejong, Republic of Korea

A system of three low-Q cavity beam position monitors (BPMs), installed in the interaction point (IP) region of the Accelerator Test Facility (ATF2) at KEK, has been designed and optimised for nanometre-level beam position resolution. The BPMs are used to provide an input to a low-latency, intra-train beam position feedback system deployed in single-pass, multi-bunch mode with the aim of demonstrating intra-train beam stabilisation on electron bunches of charge ~1 nC separated in time by 280 ns. In 2016 the BPM resolution was demonstrated to be below 50 nm using the raw measured vertical positions at the three BPMs. New results will be presented utilising integrated sampling of the raw waveforms, improved BPM alignment and modified cavities to demonstrate a vertical position resolution on the order of 20 nm.

Slides TUZGBD5 [8.557 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-TUZGBD5

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEPAL037

Simulation Study on Luminosity Feedback for Horizontal Beam Stabilization at Superkekb

2250

C.G. Pang, P. Bambade
LAL, Orsay, France
Y. Funakoshi, S. Uehara
KEK, Ibaraki, Japan

The SuperKEKB e⁺ e^- collider uses highly focused ultra-low emittance bunches colliding every 4 ns to reach a very high luminosity of 8× 10³⁵ cm^-2s^-1. It is quite essential to have an orbit feedback system at the Interaction Point (IP) to maintain the optimum overlap between the colliding beams in the presence of ground motion disturbances. For the horizontal motion, a luminosity monitoring system, based on measuring the rate of the Bhabha process at vanishing scattering angle, is developed as input signal to the feedback system. The relative precision needed for this monitor is studied in detail, for the different successive stages of luminosity operation, based on a full simulation of this system, including the detector, DAQ, lock-in amplifier, and feedback control.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-WEPAL037

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

WEPAL038

First Tests of Superkekb Fast Luminosity Monitors During 2018 Phase-2 Commissioning

2254

C.G. Pang, P. Bambade, S. Di Carlo, D. Jehanno, V. Kubytskyi, Y. Peinaud, C. Rimbault
LAL, Orsay, France
Y. Funakoshi, S. Uehara
KEK, Ibaraki, Japan

The SuperKEKB e⁺e^- collider aims to reach a very high luminosity of 8× 10³⁵ cm^-2s^-1, by using highly focused ultra-low emittance bunches colliding every 4 ns, it is essential to have an orbit feedback system at the Interaction Point (IP) to maintain the optimum overlap between two colliding beams. Luminosity monitoring systems including LumiBelle2 and ZDLM as input to dithering feedback system used to stabilize the horizontal orbit at the IP were developed and will be described, including the detectors, mechanical set-up, DAQ. Preliminary measurements and analysis of background and first stage luminosity monitoring data collected will be reported and compared with simulation.

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-WEPAL038

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)

THYGBE4

Early Phase 2 Results of LumiBelle2 for the SuperKEKB Electron Ring

2934

S. Di Carlo, P. Bambade, D. Jehanno, V. Kubytskyi, C.G. Pang, Y. Peinaud, C. Rimbault
LAL, Orsay, France

We report on the early SuperKEKB Phase 2 operations of the fast luminosity monitor (LumiBelle2 project). Fast luminosity monitoring is required by the dithering feedback system, which is used to stabilize the beam in the presence of horizontal vibrations. In this report, we focus on the operations related to the electron side of LumiBelle2. Diamond sensors are located 30 meters downstream of the IP, just above, beside, and below the electron beam pipe. During early Phase 2, the sensors are used to measure the background, arising from beam-gas scattering. We present the hardware design, the detection algorithm, and the analysis of the background measurements taken up-to-date. The results are then compared with a detailed simulation of the background, in order to well understand the physical processes involved. The simulation is performed using SAD for generation and tracking purposes, while Geant4 is used to calculate the energy deposition in the diamond sensors.

Slides THYGBE4 [3.091 MB]

DOI •

reference for this paper ※ https://doi.org/10.18429/JACoW-IPAC2018-THYGBE4

Export •

reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)